ZEBRA Z4MPLUS 200 DPI DRIVERS

Reconfigure the printer using the User Guide. Ensure the media is against the back of the transmissive sensor. Then, slide in the media guide until it just touches, but does not restrict, the edge of the media. Corporation reserves the right to correct any such errors and disclaims liability resulting therefrom. Make a note of the orientation of the pulley and around which pulley the belt is installed.

Uploader: Fer
Date Added: 5 October 2004
File Size: 50.25 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 90628
Price: Free* [*Free Regsitration Required]

Table of Contents Add to my manuals Add. See the illustration below.

Remove the bearings and roller. Install Steer Knob and Steering Roller Pin Configuration and Functions pin Connector Cutter Mode Close the printhead assembly. The table below shows pin configuration and function for a standard PC-to-printer Centronics Parallel cable.

If there is a plastic washer present, discard zebra z4mplus 200 dpi. Fanfold Media Loading Ensure that the media is against the back of the transmissive sensor.

Supported Labeling Printers

See the User Guide for proper setup and media loading instructions. Page Preventive and Corrective Maintenance Figure zebra z4mplus 200 dpi Disconnect the reflective sensor from the main logic board P7. Carefully pack the printer in a suitable container to avoid damage during transit. Open the media door and reinstall the mounting screw and lock washer Zebra z4mplus 200 dpi the media 2200 ribbon, and close the media door.

Solution Put the printer in direct thermal mode via the front panel and remove ribbon.

Page 15 Figure Problem The printhead is under temperature. Zebra z4mplus 200 dpi Zehra Psii Board Figure One method of media loading is shown in the illustration below.

Ensure that the media is against the back of the transmissive sensor. Whenever possible, use the original container from the factory.

Refer to Figure on page Insert the two mounting screws and washer through the strike plate and into the print mechanism. Platen Assembly L Rev. See page 26 Set the printer for the correct media type. Printer Side View The illustration below is a simplified view of your printer.

For optimal print quality, set the print speed to a lower setting zebra z4mplus 200 dpi ZPL II, the driver, software, or front panel. Close the pivot bracket assembly. Change Mode L Rev.

Supported Barcode Printers

zebra z4mplus 200 dpi For the Z4Mplus, carefully push the new spindle into the main frame, then install the washer and screw previously removed. Slide the rewind media guide against the liner and tighten the thumbscrew to lock it into position.

Auto calibration occurs when the printer is turned on and each time the printer recovers from an error condition. 20 method used is specific zebra z4mplus 200 dpi the application of the printer.

Loftware supports Windows printing on thermal label printers, print and apply systems, line printers, page cutsheet printers, dot matrix printers, impact printers, and laser printers. Figure provides an example of the Feed Key Self Test label. Remove the Electronics Cover Refer to Figure z4mpuls page To print the manual completely, please, download it.

Page The third printhead has zebra z4mplus 200 dpi far fewer labels, but without proper care and maintenance, signs of abrasion and contamination buildup are evident.

斑马ZebraDesigner Pro V标签编辑软件(调用数据库)-敏用数码(上海北京深圳)|专注于条码数据处理

For dpi they must be turned around with the large part facing out. Configuration This chapter discusses detailed configuration settings. Zebra z4mplus 200 dpi the insulator onto the locator pins.

See page 65 page Don’t show me this message again. Page 63 An OE indicates an overrun error. The family driver names, as they appear in the Model field in Z4mpls Label Managerare listed in the Printer Language columns.

Supported Labeling Printers

Page 87 Configuration This chapter discusses detailed configuration settings. The back cover provided covers the parallel port.

Load The Ribbon If the media is thermal transfer material, you must load a ribbon to print labels. Swing the inside end of the steering roller assembly in an zebra z4mplus 200 dpi direction, after it clears the mounting plate, pull it out toward the inside of the rewind pan. Page 21 Related Documents How Intelligent is Your Enterprise?

0.00 avg. rating (0% score) - 0 votes